AWG wire size chart and XT30 vs XT60 for FPV
Which wire and which plug for how many amps, and what a battery lead really costs you.
Battery lead loss
Length of the lead; both wires (positive and negative) are counted.
Voltage lost
0.10V
Less voltage at the ESC means less power and earlier low-voltage warnings.
Heat in the lead
5.8W
1.63 mm copper, 2.08 mm².
AWG wire size chart
| AWG | Copper Ø | Area | Resistance | Common FPV use |
|---|---|---|---|---|
| 10 | 2.59 mm | 5.26 mm² | 3.2 mΩ/m | Big long-range and heavy-lift battery leads |
| 12 | 2.05 mm | 3.31 mm² | 5.1 mΩ/m | 6S and 7-inch battery leads, high-current builds |
| 14 | 1.63 mm | 2.08 mm² | 8.1 mΩ/m | 5-inch battery leads (the usual choice) |
| 16 | 1.29 mm | 1.31 mm² | 12.8 mΩ/m | 3- to 4-inch battery leads |
| 18 | 1.02 mm | 0.82 mm² | 20.4 mΩ/m | 2- to 3-inch and toothpick battery leads |
| 20 | 0.81 mm | 0.52 mm² | 32.5 mΩ/m | Small builds' battery leads, motor wires on 5-inch |
| 22 | 0.64 mm | 0.33 mm² | 51.6 mΩ/m | Motor wires on small builds |
| 24 | 0.51 mm | 0.20 mm² | 82.1 mΩ/m | VTX and camera power |
| 26 | 0.40 mm | 0.13 mm² | 130.5 mΩ/m | Signal wires: receiver, VTX control, GPS |
| 28 | 0.32 mm | 0.08 mm² | 207.5 mΩ/m | Signal wires, LED strips |
| 30 | 0.25 mm | 0.05 mm² | 329.9 mΩ/m | Signal wires on whoops, tiny receivers |
Copper size only; insulation adds to the outside diameter. Silicone wire with many fine strands is the norm on quads because it bends and survives crashes.
XT30 vs XT60 vs XT90
| Connector | Continuous | Short burst | Usually on |
|---|---|---|---|
| XT30 | 15 A | 30 A | 2- to 3-inch, toothpicks, small packs |
| XT60 | 30 A | 60 A | 4- to 7-inch, chargers |
| XT90 | 40 A | 90 A | Heavy-lift, big long-range packs |
The ratings commonly quoted from AMASS, the maker. The number in the name is roughly the burst rating, not the continuous one. Real limits depend on the wire soldered to it and how hot the connector may get, which is why a 5-inch pulling 100 A in punch-outs lives fine on an XT60: the bursts last seconds. Whoops use small plugs such as PH2.0, BT2.0 and GNB27.
Questions
- What wire gauge for a 5-inch battery lead?
- 14 AWG is the usual choice; 12 AWG on power-hungry 6S builds. Keep the lead short: length adds resistance just like thinner wire does.
- What's the difference between XT30 and XT60?
- Size and current. XT30 is commonly rated around 15 A continuous and suits 2- to 3-inch quads; XT60 around 30 A continuous and suits 4- to 7-inch. Both handle short bursts well above that.
- Does a thicker battery lead make a difference?
- A little. A 10 cm 14 AWG lead at 100 A loses about 0.16 V and makes about 16 W of heat; the same lead in 12 AWG loses about a third less. The gain is real but small next to keeping the lead short.
- What do the AWG numbers mean?
- American Wire Gauge: smaller numbers are thicker wire. Every 3 steps down roughly doubles the copper area.
Free, in your browser
Fly it before you fly it for real
The FPV Grind sim runs in the browser with a gamepad, a radio or the keyboard. No download, no account.
Open the simMore free tools
- ChecklistsTick-off checklists for the field and the bench, saved in your browser and printable.
- ELRS packet ratesEvery ExpressLRS 4.x and 3.x packet rate with its sensitivity, and a range estimate from power and antennas.
- Betaflight diffPaste diff all to see every changed setting explained, with warnings, or compare two diffs side by side.
- Arming flagsTick the arming disable flags Betaflight shows, or paste CLI status, to see what each means and how to fix it.
- Wiring helperWhich UART each add-on goes on, how to wire it, and the Betaflight Ports settings and CLI lines.
- Latency and FOVHDZero, DJI and Walksnail latency and goggle field of view, from each maker's own specs.