Betaflight arming flags decoder: why won't my drone arm
Betaflight lists exactly why your quad won’t arm. Tick the flags it shows, or paste the CLI status output, and see what each one means and how to clear it.
In the Configurator’s CLI tab type status and press Enter. Or tick the flags you see in the Setup tab or on the OSD.
Pick a flag or paste your status to see what it means and how to clear it.
Everything happens in your browser: nothing you paste is sent anywhere.
Why won’t my drone arm in Betaflight?
Betaflight blocks arming on purpose when something isn’t safe, and names the reason as an arming disable flag. The most common are RXLOSS (no receiver signal), THROTTLE (throttle not at zero), ANGLE (quad not level), MSP or CLI (the Configurator is connected) and ARMSWITCH (the arm switch was already on). Clear the flag and it arms.
How to fix a drone that won’t arm
- Disconnect the Configurator and close the CLI.
- Turn the radio on and check the receiver is bound.
- Pull the throttle stick fully down.
- Set the quad on level ground.
- Flip the arm switch off, wait five seconds after plugging in, then flip it on.
- Read the flags that are left (Setup tab, OSD or CLI status) and decode them above.
Symptoms, causes and fixes
| Symptom | Flag | Fix |
|---|---|---|
| Plugged into USB, nothing happens | MSP, CLI | Press Disconnect, or type exit in the CLI |
| Radio off or receiver not bound | RXLOSS | Bind the receiver; check Serial RX in Ports |
| Switch flips, motors stay still | THROTTLE | Throttle fully down; check it reads under 1050 |
| Tipped over or on a slope | ANGLE | Set it level, or calibrate the accelerometer |
| Arm switch was on at power-up | ARMSWITCH / ARM_SWITCH | Flip it off, then on |
| Armed right after plugging in | BOOTGRACE | Wait five seconds |
| On USB only, no battery plugged in | DSHOT_TELEM | Plug the battery in |
For the arm switch itself and a safe arming routine, see how to arm an FPV drone. Practise arming and disarming in the browser sim.
Where this comes from
Every flag, meaning and fix is checked against Betaflight’s own documentation and source code (the master branch, with the 4.4, 4.5 and 2025.12 releases checked for renamed flags):
Questions
- Where do I see why Betaflight won't arm?
- Three places: the Setup tab in the Betaflight Configurator lists the arming disable flags, the CLI command status prints them on a line starting "Arming disable flags:", and the Betaflight OSD shows the reason when you flip the arm switch. A beeper also plays a code for the most important one.
- Why does it say MSP or CLI?
- The Configurator is connected (MSP) or the CLI is open (CLI). Betaflight never arms while you're configuring it. Press Disconnect, or type exit in the CLI, which reboots the board. Unplugging the USB cable doesn't clear MSP; power the quad off and on.
- What does RXLOSS mean?
- No valid signal from the receiver. Turn the radio on, bind the receiver, and check that Serial RX is on for the right UART in Ports with the right protocol (CRSF for ExpressLRS). If the bars in the Receiver tab move with your sticks, the link is fine.
- What does ARMSWITCH or ARM_SWITCH mean?
- The arm switch is on while something else is blocking arming, or it was already on. Flip it off, clear the other flags, then arm again. Betaflight 4.5 and earlier call it ARMSWITCH; 2025.12 renamed it ARM_SWITCH.
- How do I read the beep code?
- Five short beeps, then long beeps worth 5 each, then short beeps worth 1 each. Two long beeps is 10 (BOOTGRACE); one long and two short is 7 (CRASH). The beeper only reports the lowest-numbered flag.
Free, in your browser
Fly it before you fly it for real
The FPV Grind sim runs in the browser with a gamepad, a radio or the keyboard. No download, no account.
Open the simMore free tools
- Wiring helperWhich UART each add-on goes on, how to wire it, and the Betaflight Ports settings and CLI lines.
- Latency and FOVHDZero, DJI and Walksnail latency and goggle field of view, from each maker's own specs.
- FPV spotsPlaces to fly near you, added by pilots and groups, and the groups that fly them.
- Rates calculatorDraw Betaflight, Actual, Quick, KISS and Raceflight rates, compare two sets, convert between types and fly them in the sim.
- Controller testerPlug in a radio or gamepad and check every stick, switch and channel: centring, endpoints, jitter and deadzone.
- Channel plannerEvery 5.8 GHz analog channel, and the best channels for a group flying together, clear of intermodulation.