FPV wiring helper: UARTs, receiver, VTX and GPS
Which UART each add-on goes on, how to wire it, and what to set in Betaflight.
Count the UARTs your board’s manual lists as free; some are taken by a built-in receiver or a Bluetooth chip. If the manual names a UART for the receiver, use that one and number the rest around it.
Wiring and settings, port by port
UART1
Receiver (ExpressLRS, Crossfire)
- Receiver TX → UART1 RX
- Receiver RX → UART1 TX
- 5V → 5V
- GND → GND
Ports tab: Serial Rx.
Receiver tab: Serial-based receiver, provider CRSF (set serialrx_provider = CRSF).
UART2
Digital VTX (DJI, Walksnail, HDZero)
- VTX TX → UART2 RX
- VTX RX → UART2 TX
- Power → battery voltage pad (check the VTX's voltage range)
- GND → GND
Ports tab: MSP, and Peripherals: VTX (MSP + DisplayPort).
OSD: set osd_displayport_device = MSP so the OSD is drawn in the goggles.
UART3
GPS
- GPS TX → UART3 RX
- GPS RX → UART3 TX
- 5V → 5V (or 4V5 so it powers on USB)
- GND → GND
Ports tab: Sensor input: GPS.
Configuration tab: turn on GPS; protocol UBLOX for most modules.
TX always goes to RX and RX to TX: one side talks, the other listens. Check your board’s pinout for where each UART’s pads are.
# Ports for Betaflight 4.5 and earlier (newer versions: set them in the Ports tab)
serial 0 64 115200 57600 0 115200
serial 1 131073 115200 57600 0 115200
serial 2 2 115200 57600 0 115200
saveQuestions
- How do I wire a receiver to a flight controller?
- To a free UART: receiver TX to the UART's RX pad, receiver RX to its TX pad, plus 5V and ground. Then turn on Serial Rx for that UART in the Ports tab and pick CRSF as the receiver protocol for ExpressLRS or Crossfire.
- How do I wire a DJI, Walksnail or HDZero VTX?
- Its TX and RX to a free UART (crossed), ground, and power from the battery voltage pad if the VTX takes it. Turn on MSP for that UART, pick VTX (MSP + DisplayPort) in Peripherals, and set the OSD to MSP displayport.
- What if I run out of UARTs?
- Add-ons that use one wire can share: SmartAudio or Tramp on a UART's TX pad and ESC telemetry on the same UART's RX pad. Soft serial gives a slow extra port for VTX control or a RunCam. A receiver, GPS or digital VTX needs a real UART.
- Why do TX and RX cross?
- TX is the pin that talks and RX the one that listens, so one device's TX goes to the other's RX.
Free, in your browser
Fly it before you fly it for real
The FPV Grind sim runs in the browser with a gamepad, a radio or the keyboard. No download, no account.
Open the simMore free tools
- Latency and FOVHDZero, DJI and Walksnail latency and goggle field of view, from each maker's own specs.
- FPV spotsPlaces to fly near you, added by pilots and groups, and the groups that fly them.
- Rates calculatorDraw Betaflight, Actual, Quick, KISS and Raceflight rates, compare two sets, convert between types and fly them in the sim.
- Controller testerPlug in a radio or gamepad and check every stick, switch and channel: centring, endpoints, jitter and deadzone.
- Channel plannerEvery 5.8 GHz analog channel, and the best channels for a group flying together, clear of intermodulation.
- Flight timeHow long a pack lasts, worked out from your own flights: mAh used and minutes flown, not guesses.